338xpc Cali 45cc

kano · 14th March 2010, 09:34 AM

Can anyone out there help me out with getting a husky 338xpc (cali 45cc Model) to Australia. Cheers

Drouin Tree Service · 14th March 2010, 11:01 AM

I wouldn't bother i got one sent out and offloaded it quickly.

kano · 14th March 2010, 12:02 PM

Why? What was wrong with it

Drouin Tree Service · 14th March 2010, 06:05 PM

Rev'd but not much balls,bit of a toy.

kano · 14th March 2010, 06:52 PM

I thought being a bigger engine it might have a bit more go about it! maybe i will just do a few mods on my 338xpt instead

Drouin Tree Service · 14th March 2010, 07:13 PM

Don't let me turn you off if you want to see for yourself.

kano · 14th March 2010, 07:42 PM

To be honest mate I have been trying to justify buying one for a couple of years, I dont need it as I have two perfectly good ms200t & 338xpt, I thought maybe buying a bigger engine would work better than mods on a smaller engine and still allow for mods. I have heard that the cali is down tuned to meet emmision regulations, so I thought any problems I have heard may be rectified with a carb change . It seems pretty hard to get any real opinions other than dealers so I appreciate yours

Cut4fun · 15th March 2010, 04:34 AM

I thought the bigger cc Calif saws were to make up for the epa muffler restrained saws there. Needed more cc to be the same as everyone else saws in smaller cc.

Where there is a will to open it up and fine tune etc, I bet more could be had with the cc. But like he says why bother, put the money toward a good port job on what you already have and watch the smaller cc saw wake.

kano · 15th March 2010, 07:46 AM

Yeah I think that is what I will do, Cheers

OrangeRidge · 21st October 2011, 10:43 PM

Did you get one of these ?

14th March 2010, 09:34 AM	#1
kano Sappling Join Date: Nov 2007 Location: sydney Posts: 14	338xpc Cali 45cc Can anyone out there help me out with getting a husky 338xpc (cali 45cc Model) to Australia. Cheers

14th March 2010, 11:01 AM	#2
Drouin Tree Service Veteran Heritage Status Join Date: Jan 2007 Location: Australia Posts: 1,697	Re: 338xpc Cali 45cc I wouldn't bother i got one sent out and offloaded it quickly. __________________ Drouin Tree Services \| Excavator Hire - Drouin and SE Gippsland \| Landclearing Melbourne

14th March 2010, 12:02 PM	#3
kano Sappling Join Date: Nov 2007 Location: sydney Posts: 14	Re: 338xpc Cali 45cc Why? What was wrong with it

14th March 2010, 06:05 PM	#4
Drouin Tree Service Veteran Heritage Status Join Date: Jan 2007 Location: Australia Posts: 1,697	Re: 338xpc Cali 45cc Rev'd but not much balls,bit of a toy. __________________ Drouin Tree Services \| Excavator Hire - Drouin and SE Gippsland \| Landclearing Melbourne

14th March 2010, 06:52 PM	#5
kano Sappling Join Date: Nov 2007 Location: sydney Posts: 14	Re: 338xpc Cali 45cc I thought being a bigger engine it might have a bit more go about it! maybe i will just do a few mods on my 338xpt instead

14th March 2010, 07:13 PM	#6
Drouin Tree Service Veteran Heritage Status Join Date: Jan 2007 Location: Australia Posts: 1,697	Re: 338xpc Cali 45cc Don't let me turn you off if you want to see for yourself. __________________ Drouin Tree Services \| Excavator Hire - Drouin and SE Gippsland \| Landclearing Melbourne

14th March 2010, 07:42 PM	#7
kano Sappling Join Date: Nov 2007 Location: sydney Posts: 14	Re: 338xpc Cali 45cc To be honest mate I have been trying to justify buying one for a couple of years, I dont need it as I have two perfectly good ms200t & 338xpt, I thought maybe buying a bigger engine would work better than mods on a smaller engine and still allow for mods. I have heard that the cali is down tuned to meet emmision regulations, so I thought any problems I have heard may be rectified with a carb change . It seems pretty hard to get any real opinions other than dealers so I appreciate yours

15th March 2010, 04:34 AM	#8
Cut4fun Former Member Join Date: Dec 2009 Location: midwest Posts: 589	Re: 338xpc Cali 45cc I thought the bigger cc Calif saws were to make up for the epa muffler restrained saws there. Needed more cc to be the same as everyone else saws in smaller cc. Where there is a will to open it up and fine tune etc, I bet more could be had with the cc. But like he says why bother, put the money toward a good port job on what you already have and watch the smaller cc saw wake.

15th March 2010, 07:46 AM	#9
kano Sappling Join Date: Nov 2007 Location: sydney Posts: 14	Re: 338xpc Cali 45cc Yeah I think that is what I will do, Cheers

21st October 2011, 10:43 PM	#10
OrangeRidge Sappling Join Date: Oct 2011 Location: Mapleton Queensland Australia Posts: 11	Re: 338xpc Cali 45cc Did you get one of these ?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode